Untitled
unknown
plain_text
a year ago
10 kB
5
Indexable
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.0-10-amd64] (local build) Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint F4 EG (AF) Device Model: SAMSUNG HD204UI Serial Number: S2H7J9BB305700 LU WWN Device Id: 5 0024e9 204abfd68 Firmware Version: 1AQ10001 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 5400 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sun Jan 7 11:24:53 2024 CET ==> WARNING: Using smartmontools or hdparm with this drive may result in data loss due to a firmware bug. ****** THIS DRIVE MAY OR MAY NOT BE AFFECTED! ****** Buggy and fixed firmware report same version number! See the following web pages for details: http://knowledge.seagate.com/articles/en_US/FAQ/223571en https://www.smartmontools.org/wiki/SamsungF4EGBadBlocks SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (20700) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 345) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 100 100 051 Pre-fail Always - 4155 2 Throughput_Performance 0x0026 252 252 000 Old_age Always - 0 3 Spin_Up_Time 0x0023 083 068 025 Pre-fail Always - 5368 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 209 5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 252 252 051 Old_age Always - 0 8 Seek_Time_Performance 0x0024 252 252 015 Old_age Offline - 0 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 20382 10 Spin_Retry_Count 0x0032 252 252 051 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 252 252 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 233 181 Program_Fail_Cnt_Total 0x0022 001 001 000 Old_age Always - 4008956520 191 G-Sense_Error_Rate 0x0022 100 100 000 Old_age Always - 20 192 Power-Off_Retract_Count 0x0022 252 252 000 Old_age Always - 0 194 Temperature_Celsius 0x0002 064 049 000 Old_age Always - 36 (Min/Max 15/51) 195 Hardware_ECC_Recovered 0x003a 100 100 000 Old_age Always - 0 196 Reallocated_Event_Count 0x0032 252 252 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 252 252 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 252 252 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0036 035 035 000 Old_age Always - 34585 200 Multi_Zone_Error_Rate 0x002a 100 100 000 Old_age Always - 10362 223 Load_Retry_Count 0x0032 252 252 000 Old_age Always - 0 225 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 233 SMART Error Log Version: 1 ATA Error Count: 49386 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 49386 occurred at disk power-on lifetime: 119 hours (4 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 01 47 01 00 e0 Error: ICRC, ABRT at LBA = 0x00000147 = 327 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ca 00 08 40 01 00 e0 00 00:03:49.372 WRITE DMA ea 00 00 00 00 00 40 00 00:03:49.372 FLUSH CACHE EXT 35 00 20 18 5f 36 40 00 00:03:49.372 WRITE DMA EXT 35 00 28 18 77 70 40 00 00:03:49.372 WRITE DMA EXT 35 00 28 58 37 87 40 00 00:03:49.372 WRITE DMA EXT Error 49385 occurred at disk power-on lifetime: 119 hours (4 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 01 5f 03 00 e0 Error: ICRC, ABRT at LBA = 0x0000035f = 863 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ca 00 08 58 03 00 e0 00 00:03:48.881 WRITE DMA ca 00 08 58 01 00 e0 00 00:03:48.881 WRITE DMA ea 00 00 00 00 00 40 00 00:03:48.881 FLUSH CACHE EXT 35 00 28 70 5a 36 40 00 00:03:48.881 WRITE DMA EXT 35 00 20 38 68 70 40 00 00:03:48.881 WRITE DMA EXT Error 49384 occurred at disk power-on lifetime: 119 hours (4 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 01 5f 01 00 e0 Error: ICRC, ABRT at LBA = 0x0000015f = 351 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ca 00 08 58 01 00 e0 00 00:03:41.205 WRITE DMA ea 00 00 00 00 00 40 00 00:03:41.205 FLUSH CACHE EXT 35 00 30 b8 21 36 40 00 00:03:41.205 WRITE DMA EXT 35 00 30 a0 bc 6f 40 00 00:03:41.205 WRITE DMA EXT 35 00 28 80 30 e6 40 00 00:03:41.205 WRITE DMA EXT Error 49383 occurred at disk power-on lifetime: 119 hours (4 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 01 0f 03 00 e0 Error: ICRC, ABRT at LBA = 0x0000030f = 783 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ca 00 08 08 03 00 e0 00 00:03:39.371 WRITE DMA ca 00 08 08 01 00 e0 00 00:03:39.371 WRITE DMA ea 00 00 00 00 00 40 00 00:03:39.371 FLUSH CACHE EXT 35 00 20 b8 0f 36 40 00 00:03:39.371 WRITE DMA EXT 35 00 10 a0 0f 36 40 00 00:03:39.371 WRITE DMA EXT Error 49382 occurred at disk power-on lifetime: 119 hours (4 days + 23 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 01 5f 03 00 e0 Error: ICRC, ABRT at LBA = 0x0000035f = 863 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ca 00 08 58 03 00 e0 00 00:03:37.490 WRITE DMA ca 00 08 58 01 00 e0 00 00:03:37.490 WRITE DMA c8 00 08 08 71 00 e7 00 00:03:37.490 READ DMA ea 00 00 00 00 00 40 00 00:03:37.490 FLUSH CACHE EXT 35 00 08 a8 51 6f 40 00 00:03:37.490 WRITE DMA EXT SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 5191 - SMART Selective self-test log data structure revision number 0 Note: revision number not 1 implies that no selective self-test has ever been run SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Completed [00% left] (0-65535) 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
Editor is loading...
Leave a Comment