Untitled
unknown
plain_text
9 months ago
11 kB
5
Indexable
[srv30.zload][root@~] > smartctl -a /dev/sdd
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.0-26-amd64] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: ST18000NM000J-2TV103
Serial Number: ZR5DFC3L
LU WWN Device Id: 5 000c50 0e6043eb6
Firmware Version: SN04
User Capacity: 18,000,207,937,536 bytes [18.0 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-4 (minor revision not indicated)
SATA Version is: SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sun Jan 19 09:23:41 2025 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 575) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: (1603) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x70bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 071 045 044 Pre-fail Always - 143336232
3 Spin_Up_Time 0x0003 095 095 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 5
5 Reallocated_Sector_Ct 0x0033 099 099 010 Pre-fail Always - 226
7 Seek_Error_Rate 0x000f 090 060 045 Pre-fail Always - 916725440
9 Power_On_Hours 0x0032 088 088 000 Old_age Always - 11181
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 5
18 Unknown_Attribute 0x000b 100 100 050 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 109
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 1
190 Airflow_Temperature_Cel 0x0022 070 067 000 Old_age Always - 30 (Min/Max 26/33)
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 3
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 479
194 Temperature_Celsius 0x0022 030 040 000 Old_age Always - 30 (0 26 0 0 0)
197 Current_Pending_Sector 0x0012 099 098 000 Old_age Always - 260
198 Offline_Uncorrectable 0x0010 099 098 000 Old_age Offline - 260
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0023 100 100 001 Pre-fail Always - 0
240 Head_Flying_Hours 0x0000 100 100 000 Old_age Offline - 11128 (115 74 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 19011371984
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 3030941398256
SMART Error Log Version: 1
ATA Error Count: 26243 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 26243 occurred at disk power-on lifetime: 11181 hours (465 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 78 ff ff ff 4f 00 16d+06:47:30.818 READ FPDMA QUEUED
60 00 98 ff ff ff 4f 00 16d+06:47:30.818 READ FPDMA QUEUED
60 00 68 ff ff ff 4f 00 16d+06:47:30.818 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 16d+06:47:30.785 READ FPDMA QUEUED
60 00 f8 ff ff ff 4f 00 16d+06:47:30.785 READ FPDMA QUEUED
Error 26242 occurred at disk power-on lifetime: 11181 hours (465 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 80 ff ff ff 4f 00 16d+06:47:00.275 READ FPDMA QUEUED
60 00 80 ff ff ff 4f 00 16d+06:47:00.275 READ FPDMA QUEUED
60 00 40 ff ff ff 4f 00 16d+06:47:00.199 READ FPDMA QUEUED
60 00 40 ff ff ff 4f 00 16d+06:47:00.196 READ FPDMA QUEUED
60 00 c0 ff ff ff 4f 00 16d+06:47:00.196 READ FPDMA QUEUED
Error 26241 occurred at disk power-on lifetime: 11181 hours (465 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 ff ff ff 4f 00 16d+06:46:57.955 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 16d+06:46:57.955 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 16d+06:46:57.955 READ FPDMA QUEUED
60 00 c0 ff ff ff 4f 00 16d+06:46:57.953 READ FPDMA QUEUED
60 00 40 ff ff ff 4f 00 16d+06:46:57.953 READ FPDMA QUEUED
Error 26240 occurred at disk power-on lifetime: 11181 hours (465 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 ff ff ff 4f 00 16d+06:45:47.303 READ FPDMA QUEUED
60 00 60 ff ff ff 4f 00 16d+06:45:45.825 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 16d+06:45:45.816 READ FPDMA QUEUED
60 00 f8 ff ff ff 4f 00 16d+06:45:45.816 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 16d+06:45:45.816 READ FPDMA QUEUED
Error 26239 occurred at disk power-on lifetime: 11181 hours (465 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 48 ff ff ff 4f 00 16d+06:45:45.096 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 16d+06:45:45.083 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 16d+06:45:44.593 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 16d+06:45:44.284 READ FPDMA QUEUED
60 00 20 ff ff ff 4f 00 16d+06:45:44.246 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.Editor is loading...
Leave a Comment